How to hang a wreath on any door

norsu STUDIO iridescent perspex Christmas wreath with hand-tied ribbon bow, bell and perspex stars
The norsu edit · Christmas
How to hang a wreath on any door
One hook on the inside of the door, the right height, two minutes, and nothing to show for it in January. Glass doors included.
Christmas·Wreaths·Words by the norsu team

Every December the same message lands in our inbox: “I love the wreath. How do I get it on the door without wrecking it?”

Good news. You don’t need a drill, a nail or a roll of tape. You need one hook rated for the weight, the right spot, and about two minutes. Here’s the short version, then the detail for your door.

The short version
  1. Go over the limit. Our wreaths are lighter than they look, but we always choose a hook rated well above what we’re hanging. Nearly every hook here holds 3kg or more, and the one that doesn’t still has weight to spare. Better safe than finding it on the doormat.
  2. Timber or painted door? One Command Jumbo hook (holds 3.4kg) stuck upside down on the inside of the door at the top. Ribbon over the top edge, knot onto the hook. Done.
  3. Glass or screen door? A Zip ’n Hang (holds 3.6kg). Two clear lines loop over the top corners and a small hook sits on the front. Nothing is stuck to the glass. On a clear glass door under cover, a Command Large Clear hook (holds 1.8kg) straight onto the pane is the simpler option.
  4. Stained glass or leadlight door? Go the Small and drop it below the glass, onto the solid timber panel. Same hook on the inside, just a longer run of ribbon. The leadlight stays the star.
  5. Where should it sit? Centre of the wreath at eye level, about 150 to 160cm off the ground, centred on the door. Not up near the top rail.
“Most wreaths aren’t hung wrong. They’re hung too high.”
First, the wreath
What you’re actually hanging

Our wreaths are cut from a single sheet of iridescent perspex in a soft scalloped shape, so they sit flat against the door. They shift from teal to pink to amber as the light moves across them. Each one is finished by hand in our Melbourne studio with an oversized bow of our own patterned ribbon, a bell and perspex stars, so no two are exactly alike. The ribbon is tied off with a knot at the end, and that knot is what you hang it by.

The Large is made for a front door. The Small suits a bedroom or pantry door, a mirror or a mantel, and it’s the one for a stained glass front door, hung below the leadlight. We made a very small number of each. Neither is heavy, but a door swings and wind gets under a bow, so we always choose a hook rated well above what we’re hanging. Nearly every hook below holds 3kg or more, which leaves plenty in hand. The one exception, the clear hook for glass, is rated to 1.8kg, still well above what either wreath weighs.

Four ways to hang it
Pick the one for your door
Ranked from our favourite down. Each one names a hook with weight to spare and where to find it. All four leave no trace in January.
01
The norsu way · timber, painted and composite doors
One hook, upside down
This is how we hang ours. A single adhesive hook goes on the inside of the door, right at the top, turned upside down so the hook points to the floor. The ribbon runs up the front of the door, over the top edge, and the knot at the end pops onto the hook. From the street you see ribbon and nothing else.
The hookCommand Jumbo Utility Hook, rated to 3.4kg. Around $9.60 for a two-pack at Bunnings. Not the Large (2.2kg) or Medium (1.3kg). They would probably hold, but the Jumbo costs about the same and gives you the margin once the door swings and the wind gets under the bow.
Step by step
  1. Open the door. Wipe the top inside face with isopropyl alcohol and let it dry. No household spray; it leaves residue the adhesive can’t grip.
  2. Peel the strip, press the hook on upside down, 2 to 3cm below the top edge and centred on the door width. Hold for 30 seconds.
  3. Wait an hour before hanging anything. This is the step everyone skips and the reason hooks fall off.
  4. Drape the ribbon over the top of the door and pop the knot onto the hook.
  5. Close the door. Step outside and check the height. If it’s low, tie a second knot higher up the ribbon.
Good to know
  • Works on any door with a solid top rail: timber, painted, composite, and glass doors with a timber or aluminium frame.
  • The hook is on the inside, so it never sees sun or rain. That is why this beats sticking anything to the front of the door.
  • In January, pull the strip’s tab slowly straight down. Never pull outwards.
02
Glass, screen and security doors
The Zip ’n Hang
One of our followers put us onto this and it’s now what we suggest for every glass door. It’s a small black disc, about 7.5cm across, with two near-invisible clear lines wound inside. Loop the lines over the top two corners of the door and the disc sits on the front face with a built-in hook. A side button raises or lowers the hook to exactly the height you want. Nothing touches the glass and nothing sits over the top of the door, which is why it’s worth it for a glass door you care about.
The hangerZip ’n Hang Wreath Hanger in black, rated to 3.6kg. Around $56.60 on Amazon Australia. It ships from the US, so allow a week or two.
Step by step
  1. Open the door. Set the hook height with the side button.
  2. Pull the two clear lines out of the disc.
  3. Loop one over the top hinge-side corner of the door, the other over the top latch-side corner.
  4. Close the door and check the disc sits flat and straight on the front face.
  5. Hang the wreath by its knot. Step back, check it’s level, fluff the bow.
Where it won’t work
  • Arched doors and sliding doors. There are no square corners to loop over.
  • Doors with metal interlocking weatherstripping, which can cut the line.
The simpler option for clear glass If the door is plain clear glass and it sits under a covered porch or verandah, you can skip the lines altogether and stick one clear hook straight onto the pane. Command’s large clear hook is designed for glass, is close to invisible on it, and peels off cleanly in January. It’s rated to 1.8kg, lower than the other hooks here but still well above what our wreath weighs, and it costs less than a coffee and a croissant.
The hookCommand Large Clear Adhesive Wall Hook, rated to 1.8kg, works on glass. Around $9.40 for one hook at Bunnings. Command rates it for indoor surfaces, so keep it for a glass door that’s under cover and out of direct afternoon sun. Not the medium clear hook, which holds 900g.
Step by step
  1. Wipe the spot on the glass with isopropyl alcohol and let it dry. No glass cleaner; it leaves a film the strip can’t grip.
  2. Peel the strip, press the hook onto the glass with the hook pointing up, and hold for 30 seconds. Put it a few centimetres above where you want the knot to sit.
  3. Wait an hour before hanging anything.
  4. Hang the wreath by its knot. Step outside, check the height, fluff the bow.
03
Timber doors with a gap at the top
A slim over-the-door hanger
The classic. A thin metal bar hooks over the top edge of the door with a hook on the outside face. Nothing is stuck to anything, and the good ones are rated far beyond what you need. The catch is the gap: the bar has to fit between the top of the door and the frame, and most new doors with a weather seal won’t take one.
The hangerA slim metal over-the-door hanger around 30cm long and no more than 25mm wide, rated to 10kg or more. The matte gold one from Christmas Warehouse (about $5 through JB Hi-Fi) sits nicely against brass hardware. If you want the wreath lower, the Haute Decor Adapt adjusts from 42 to 63cm.
Step by step
  1. Check the gap. Open the door and slide a credit card into the space at the top. If it goes easily, a slim hanger will fit. If not, use method 01.
  2. Stick a strip of self-adhesive felt to the inside of the bar where it touches the door. Bare metal on paint is how you get a scratch.
  3. Slide it over the top of the door, centred on the door width, not on any glass panel.
  4. Close the door gently. If it resists, the bar is too thick for your seal. Don’t force it.
  5. Hang the wreath by its knot and check it’s level.
04
Steel doors only
A magnetic hook
If your door is steel or steel-faced, a strong magnetic hook is the tidiest option of all. Nothing to stick, nothing over the top, and it comes off in a second. The thing to understand is the rating.
The hookA neodymium magnetic hook rated to at least 10kg, rubber-coated to protect the paint. Around $10 for a four-pack on Amazon Australia or from Bunnings.
Step by step
  1. Check it’s actually steel: a fridge magnet should snap on. Aluminium screen doors and most composite doors won’t hold a magnet.
  2. Test the hook on the door with a 2kg bag of flour or sugar hanging from it, which is more than the wreath weighs. If it slides, the door skin is too thin or too textured. Use method 02 instead.
  3. Place the hook, hang the wreath by its knot, and check it after the first windy day.
Good to know
  • Why 10kg for a wreath this light? That rating is for pulling the magnet straight off the steel. On a door the wreath pulls sideways, down the face, and a magnet holds roughly a third as much that way. A 10kg magnet carries about 3kg on a door, which is the margin we like. A 5kg magnet is cutting it fine.
  • If yours is bare metal, put a scrap of felt between magnet and door.
What we’d skip
  • Suction cups. They lose grip in heat and cold and the rated capacities are for a perfectly clean, flat surface on a mild day. Not for anything you’d be sad to find on the doormat.
  • Command Large or Medium hooks at 2.2kg and 1.3kg. They would likely hold, but the Jumbo costs the same and gives you the margin.
  • Any adhesive hook on the outside of a sun-facing door. The adhesive softens in summer heat and lets go. Keep adhesive on the inside face, out of the sun.
  • Bare metal over-door hooks without padding. They scratch paint and dent timber at the top edge.
Match the method
Which one for your door
01

Painted or stained timber door

Best: Command Jumbo on the inside, upside down (01). Also: metal over-door hanger with felt (03) if there’s a gap at the top.
02

Glass front door, or a door with a big glass panel

Best: Zip ’n Hang (02). Also: a Command Large Clear hook straight onto clean glass if the door is under cover (02), or a Command Jumbo on the inside of the top rail if the door has a solid frame (01). Not: suction cups, or any adhesive on glass that cops full afternoon sun.
03

Stained glass or leadlight door

Everywhere in Melbourne, from the Federation villa to the Edwardian terrace. Don’t cover the glass. Best: the Small, hung from a Command Jumbo on the inside of the top rail (01), with the ribbon run long so the wreath sits on the solid timber panel below the leadlight. If you need more drop, tie on a length of our satin ribbon. Also: a Command Jumbo on the front of the timber rail just beneath the glass, if you’d rather the ribbon didn’t cross it. Not: the Large across the glass, and nothing stuck to the leadlight itself.
04

Screen or security door

Best: Zip ’n Hang looped over the screen frame (02). Not: magnets, because most screen frames are aluminium. Not: hooks through the mesh.
05

Steel door

Best: 10kg magnetic hook (04). Also: Zip ’n Hang (02), or Command Jumbo on the inside (01).
06

Apartment or fire-rated door

Best: Command Jumbo on the inside (01) or Zip ’n Hang (02). Not: over-door hangers, which can stop a self-closing door from closing. Check your building rules first.
07

Arched or sliding door

Best: Command Jumbo on the wall or frame beside the door, and hang the wreath there. Not: Zip ’n Hang, which needs square top corners.
08

Internal door, mirror or mantel

Best: Command Jumbo, upside down on the back of the door (01), or on the wall above a mantel. Indoors, out of the sun, it will hold all season.
Where to hang it — the quick rules
  1. Centre it on the door, not the glass. If there’s a glass panel to one side, ignore it. The eye reads the whole door.
  2. Leadlight up top? Hang below it. On a stained glass door the glass is the feature. Use the Small, centre it on the timber panel underneath, and let it sit lower than the eye-level rule. Centred on the panel, it reads as deliberate.
  3. Eye level, or a touch above. Centre of the wreath about 150 to 160cm off the ground. On a standard 2.04m door that’s the upper third, not kissing the top rail.
  4. Clear the hardware. Don’t overlap the handle, peephole or knocker. If it does, go up a little or choose the Small.
  5. Let the tails fall. Our bows are tied so the ribbon moves in the breeze. If it catches on the handle, drape it to one side rather than tucking it away.
  6. Check it at night. Porch light hits perspex beautifully. Step out after dark and see.
Beyond the front door
Four more places it works
The Small was made for the spots inside the house that a front-door wreath never reaches.
01

Over the hallway mirror

Ribbon over the top of a leaner mirror, knot behind. On a wall-hung mirror, a Command Jumbo on the wall just above the frame. The iridescence doubles in the reflection.
02

Above the mantel

A Command Jumbo on the chimney breast, wreath hung from the knot. Run our bells and baubles along the shelf beneath it.
03

Bedroom and pantry doors

The Small, hung the norsu way with a Command Jumbo on the back of the door. One per door down a hallway, all at the same height, is quietly spectacular.
04

Over a staircase balustrade

Ribbon over the handrail with the knot tucked behind, so the wreath hangs on the outside where it reads from the hall below. One on the newel post at the bottom of the flight, or a run of Smalls down the stairs at even spacings. Nothing is fixed to the timber, so it comes off in January without a mark.
Looking after it
Caring for a perspex wreath
  • Keep it under cover. Perspex is weatherproof. A covered porch keeps the ribbon crisp. If the bow gets wet, dry it flat and reshape by hand.
  • Microfibre only. No paper towel and no ammonia glass cleaner. Both can haze the surface.
  • Keep the box. Lay it flat, tails tucked under the bow, and it comes out next year exactly as it arrived.
  • Hooks off properly. Pull the Command strip’s tab slowly straight down, never outwards. Zip ’n Hang and magnets just lift off.
Common questions

Hanging a wreath, answered

How heavy is a norsu wreath, and what hook rating do I need?
Lighter than it looks. The perspex is thin and flat, and the bow, bell and stars add very little. Even so, we always choose a hook rated well above what we’re hanging, because a door swings and wind gets under the bow. Nearly every hook we recommend holds 3kg or more: Command Jumbo (3.4kg), Zip ’n Hang (3.6kg), a metal over-door hanger (typically 9 to 11kg) or a 10kg magnetic hook on a steel door. The one exception is the Command Large Clear hook for glass doors, rated to 1.8kg, still well above what either wreath weighs.
How do I hang a wreath on a glass door without suction cups?
Use a Zip ’n Hang. Two fine clear lines loop over the top corners of the door and a small hook sits on the glass face. Nothing is stuck to the glass and the door seal is unaffected. It holds 3.6kg. On a clear glass door under cover, a Command Large Clear hook stuck straight onto the pane also works; see method 02.
How do I hang a wreath on a stained glass or leadlight door?
Don’t hang it over the glass. Use the Small and drop it below the leadlight so it sits on the solid timber panel. A Command Jumbo on the inside of the top rail with the ribbon run long does it, or a Jumbo on the front of the timber rail just under the glass if you’d rather keep the ribbon off it. Nothing gets stuck to the leadlight itself.
Can I use a Command hook on a glass door?
Yes, with the right one. The Command Large Clear Adhesive Wall Hook is made for glass, is rated to 1.8kg and comes off cleanly. Clean the glass with isopropyl alcohol, press for 30 seconds and give it an hour before hanging. Command rates it for indoor surfaces, so use it on a glass door under a covered porch and out of direct sun. Skip the medium clear hook at 900g. If the glass door has a solid timber or aluminium frame, a Command Jumbo on the inside of the top rail with the ribbon run over the top is the other option.
Will an over-the-door wreath hook damage my door?
A bare metal hanger can scratch paint or dent timber at the top edge, and a thick one can crush the draught seal. Stick felt to the back of the bar, check the gap with a credit card first, or use the Command Jumbo method on the inside of the door instead.
How do I hang a wreath on a screen door?
Loop a Zip ’n Hang over the top corners of the screen frame. Don’t hook the wreath through the mesh, and don’t rely on magnets: most screen frames are aluminium, which isn’t magnetic.
Can I hang a wreath on a rental property door?
Yes. A Command hook on the inside of the door, a Zip ’n Hang, and a magnetic hook on a steel door all leave no trace. Avoid nails, screws and adhesive on the outside of a door in full sun.
What height should a Christmas wreath be hung?
Centre the wreath roughly at eye level, about 150 to 160cm from the ground, and centred on the width of the door. Don’t overlap the handle or peephole.
Is the norsu iridescent wreath suitable for outdoors?
Yes, under a covered porch or verandah. The perspex is weatherproof. Keep the ribbon bow out of direct rain where you can.
Show us
Your wreath, your door
Tag @norsuinteriors with your wreath on your door. We want to see the glass doors especially. And if you haven’t got yours yet, there are very few left.
Shop the Christmas edit
  |  

More Posts